New nanocomposite based on poly(lactic-co-glycolic acid) copolymer and magnetite. Synthesis and characterization

The study presents the preparation of the new magnetic nanocomposite based on PLGA and magnetite. The PLGA used to obtain the magnetic nanocomposites was synthesized by the copolymerization of lactic acid with glycolic acid, in the presence of tin octanoate [Sn(Oct)₂] as catalyst, by polycondensation procedure. Magnetite was obtained by co-precipitation from aqueous salt solutions FeCl₂/FeCl₃. The particles size of magnetite was 420 nm, and the saturation magnetization 62.78 emu/g, while the PLGA/magnetite nanocomposite size was 864 nm and the saturation magnetization 39.44 emu/g. The magnetic nanocomposites were characterized by FT-IR, DLS technique, SEM, VSM and simultaneous thermal analyses (TG–FTIR–MS). The polymer matrix PLGA acts as a shell and carrier for the active component, while magnetite is the component which makes targeting possible by external magnetic field manipulation. Based on the gases resulted by thermal degradation of PLGA copolymer, using the simultaneous analysis TG–FTIR–MS, a possible degradation mechanism was proposed.     

Characteristics and formation mechanism of porosities in CFRP during laser joining of CFRP and steel

An experimental investigation on the mechanism of porosity formation during the laser joining of carbon fiber reinforced polymer (CFRP) and steel is presented. The porosity morphology and distribution were characterized by optical and scanning electron microscopy, and the thermal pyrolysis behaviors were investigated by thermal analysis and designed back-side cooling experiments. The results show that there are two types of porosities in CFRP. Porosity I only appears when the heat input is more than 77.8 J/mm. It has a smooth inner wall and distributes near the bonding interface between CFRP and steel at the central area of melted zone, which is caused by gaseous products such as CO₂, NH₃, H₂O, and hydrocarbons produced by the pyrolysis of CFRP. Porosity II can be seen under all joining conditions. It has a rough inner wall and distributes far away from the bonding interface, concentrating at the final solidification locations. Porosity II is caused by the shrinkage of melted CFRP during solidification stage.     

Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

Reactive Oxygen and Nitrogen Species in Defense/Stress Responses Activated by Chitosan in Sycamore Cultured Cells

Chitosan (CHT) is a non-toxic and inexpensive compound obtained by deacetylation of chitin, the main component of the exoskeleton of arthropods as well as of the cell walls of many fungi. In agriculture CHT is used to control numerous diseases on various horticultural commodities but, although different mechanisms have been proposed, the exact mode of action of CHT is still unknown. In sycamore (Acer pseudoplatanus L.) cultured cells, CHT induces a set of defense/stress responses that includes production of H₂O₂ and nitric oxide (NO). We investigated the possible signaling role of these reactive molecules in some CHT-induced responses by means of inhibitors of production and/or scavengers. The results show that both reactive nitrogen and oxygen species are not only a mere symptom of stress conditions but are involved in the responses induced by CHT in sycamore cells. In particular, NO appears to be involved in a cell death form induced by CHT that shows apoptotic features like DNA fragmentation, increase in caspase-3-like activity and release of cytochrome c from the mitochondrion. On the contrary, reactive oxygen species (ROS) appear involved in a cell death form induced by CHT that does not show these apoptotic features but presents increase in lipid peroxidation.     

Rapid detection of viable Bacillus cereus emetic and enterotoxic strains in food by coupling propidium monoazide and multiplex PCR (PMA-mPCR)

Bacillus cereus can cause emetic and diarrheal food poisoning. It is widespread in nature and therefore, considered a major foodborne pathogen. To develop a sensitive and reliable assay for detecting enterotoxin genes (nheA, entFM, hblD, cytK) and emetic toxin (ces), specific primers each targeting one individual gene were designed. Propidium monoazide (PMA) was coupled with the developed multiplex PCR (mPCR) for the detection of viable B. cereus. The inclusivity and exclusivity of the PMA-mPCR was confirmed using a panel of 44 strains including 17 emetic and 9 enterotoxic B. cereus reference strains and 18 non-target strains. The limit of detection (LOD) without PMA treatment in pure DNA was 2 pg/reaction tube. The LOD of mPCR assay in pure heat-killed dead bacteria was 4.0 × 10² CFU/mL. Also, the LOD on the viable bacteria with or without PMA treatment was similar (3.8 × 10² CFU/mL) showing that the PMA treatment did not significantly decrease sensitivity. Finally, the newly developed PMA-mPCR successfully detected 4.8 × 10³ and 3.6 × 10³ CFU/g of viable B. cereus F4810/72 (emetic) and B. cereus ATCC 12480 (enterotoxic) reference strains, respectively, in food samples. Hence, this study combines PMA and mPCR to detect viable B. cereus with a wide range of toxin detection (5 toxins). Thus, the novel PMA-mPCR assay developed in this study is a rapid and efficient diagnostic tool for the monitoring of viable B. cereus in food samples and potentially other samples via appropriate DNA extraction.     

Hydrocarbon-based electrode ionomer for proton exchange membrane fuel cells

The electrode ionomer is a key factor that significantly affects the catalyst layer morphology and fuel cell performance. Herein, sulfonated poly(arylene ether sulfone)-based electrode ionomers with polymers of various molecular weights and alcohol/water mixtures were prepared, and those comprising the alcohol/water mixture showed a higher performance than the ones prepared using higher boiling solvents, such as dimethylacetamide; this is owing to the formation of the uniformly dispersed ionomer catalyst layer. The relation between ionomer molecular weight for the same polymer structure and the sulfonation degree was investigated. Because the chain length of polymer varies with molecular weight and chain entanglement degree, its molecular weight affects the electrode morphology. As the ionomer covered the catalyst, the agglomerates formed were of different morphologies according to their molecular weight, which could be deduced indirectly through dynamic light scattering and scanning electron microscopy. Additionally, the fuel cell performance was confirmed in the current-voltage curve.     

浅析混凝土搅拌站的防雷

近年来,我市因雷击而导致搅拌站系统瘫痪停产、影响工程进度的事件时有发生,在针对混凝土搅拌站配料秤的实际检定工作中,也常发现配料秤的称重传感器因雷击损坏而影响计量准确性。因此,对混凝土搅拌站防雷的研究具有重要意义。本文阐述了雷电对混凝土搅拌站的主要危害,分析了混凝土搅拌站常见的雷击原因及其防护措施,旨在引起生产方、安装方以及使用方对混凝土搅拌站防雷的共同重视。     

基于空气质量模拟的江苏省大气污染物排放清单比较研究

大气污染物排放清单是空气质量模拟和空气污染治理的重要依据.本研究比较分析了两套覆盖江苏省的2017年大气污染物排放清单，即分别由上海市环境科学研究院、江苏省环境科学研究院编制的"长三角清单"和"江苏省清单"，并结合区域空气质量模型CMAQ评估不同清单对长三角地区2017年1、4、7、10月的空气质量模拟的影响.清单比较结果表明，除二氧化硫（SO₂）以外，江苏省清单估算的各污染物排放量较长三角清单低.通过与观测数据比较，发现两套清单对SO₂、氮氧化物（NO_x）、臭氧（O₃）和细颗粒物（PM_2.5）的模型模拟性能均较好.江苏省清单与长三角清单两者的模拟结果空间分布接近，其中江苏省清单模拟的PM_2.5和O₃在长三角多数地区略低于长三角清单的模拟结果（1月O₃除外）.江苏省清单与长三角清单均能够用于空气质量模式模拟，可为江苏地区的细颗粒物和光化学烟雾污染的控制策略制定提供参考.     

Formulation of sage essential oil (Salvia officinalis,L.) monoterpenes into chitosan hydrogels and permeation study with GC-MS analysis

This study deals with the formulation of natural drugs into hydrogels. For the first time, compounds from the sage essential oil were formulated into chitosan hydrogels. A sample preparation procedure for hydrophobic volatile analytes present in a hydrophilic water matrix along with an analytical method based on the gas chromatography coupled with the mass spectrometry (GC-MS) was developed and applied for the evaluation of the identity and quantity of essential oil components in the hydrogels and saline samples. The experimental results revealed that the chitosan hydrogels are suitable for the formulation of sage essential oil. The monoterpene release can be effectively controlled by both chitosan and caffeine concentration in the hydrogels. Permeation experiment, based on a hydrogel with the optimized composition [3.5% (w/w) sage essential oil, 2.0% (w/w) caffeine, 2.5% (w/w) chitosan and 0.1% (w/w) Tween-80] in donor compartment, saline solution in acceptor compartment, and semi-permeable cellophane membrane, demonstrated the useful permeation selectivity. Here, (according to lipophilicity) an enhanced permeation of the bicyclic monoterpenes with antiflogistic and antiseptic properties (eucalyptol, camphor and borneol) and, at the same time, suppressed permeation of toxic thujone (not exceeding its permitted applicable concentration) was observed. These properties highlight the pharmaceutical importance of the developed chitosan hydrogel formulating sage essential oil in the dermal applications.